Zoom MRS-4 Specifications download pdf (Page 40)

Reference [Recorder]

ZOOM MRS-1608

Using auto punch-in/out

Auto punch-in/out is a function that lets you specify

beforehand the region to be re-recorded. Punch-in will occur

automatically when you reach the starting location (In

point), and punch-out will occur automatically when you

reach the ending location (Out point). This is convenient

when you cannot operate the MRS-1608 because you are

playing the instrument yourself, or when very fast playback/

record switching is required.

In order to perform auto punch-in/out, you must ﬁrst

specify the In point (the point where the recorder

switches from playback to record) and Out point (the

point where the recorder switches from record to

playback), and then perform the recording operation.

Raise the fader of the track on which you

want to perform punch-in/out to a suitable

position.

Use the [ON/OFF] key to select the input,

and then play your instrument connected to

the INPUT jack and use the [INPUT] control

and [REC LEVEL] control to adjust the

recording level.

Locate the point at which you want to

punch-in, and press the [AUTO PUNCH IN/

OUT] key.

The key ﬂashes. This sets the “In point” at which recording

will begin.

Locate the point at which you want to

punch-out, and press the [AUTO PUNCH

IN/OUT] key once more.

The key changes from ﬂashing to solidly lit. This sets the

“Out point” at which recording will end.

HINT

To specify the in/out points precisely, it is convenient to use

the scrub function (

→

p. 38) to ﬁnd the locations and assign

a mark (

→

p. 46) beforehand at the desired locations.

Use the Locate function to go to a spot

before the In point.

Repeatedly press the status key for the

track on which you want to perform punch-

in/out, until the key ﬂashes red.

NOTE

If the current location is between the In point and Out point,

the status key (and the REC [

] key if during recording) will

be lit red. In this case, use the locate function once again to

go to a point that is earlier than the In point.

To rehearse the auto punch-in/out process,

press the PLAY [R

] key.

The recorder will begin playing. When you reach the In

point, the track on which you are punching-in/out will be

muted. When you reach the Out point, muting will be

defeated. (You will always be able to monitor the input

signal during this time.) Performing this action will not

delete or record anything on the track.

When you have ﬁnished rehearsing, move again to a

location earlier than the In point.

HINT

To change the positions of the In point or Out point, press the

[AUTO PUNCH IN/OUT] key so that the key goes out, and

then repeat steps 3 – 7.

To actually perform auto punch-in/out, hold

down the REC [

] key and press the PLAY

[

] key.

The recorder will begin playing. When you reach the In

point, recording will begin automatically (punch-in).

When you reach the Out point, recording will end

automatically, and playback will resume (punch-out).

When you have ﬁnished recording, press

the STOP [

] key.

10.

To listen to the recorded result, repeatedly

press the status key for the track on which

you recorded, until the key is lit green. Then

move to a location earlier than the In point,

and press the PLAY [

] key.

To re-do the punch-in/punch-out recording, repeat steps

5 – 9.

11.

When you are satisﬁed with the recording,

press the [AUTO PUNCH IN/OUT] key so

that the key goes out.

The auto punch-in/out function is turned off, and the In

point and Out point settings are cleared.

In point Out point

Track

PlaybackPlayback Recording

1608E.book 40 ページ２００４年４月１９日　月曜日　午前１０時４４分

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 223 224

Zoom MRS-4 Specifications Page 40

Comments to this Manuals

Zoom MRS-4 Specifications Page 40

Comments to this Manuals

Related products and manuals for Recording Equipment Zoom MRS-4