Zoom Pro 4040 Specifications download pdf (Page 6)

Pressing this key switches from Play mode to Edit mode.

The Edit mode can also be used as Manual mode to switch

effect modules on and off with the pedal switches 1 – 4 and

the BANK ▼ pedal. The key also serves to return from the

Edit mode to the Play mode, and to cancel a store process.

(11) BANK pedal switches

• In Play mode

The ▲ pedal selects the next higher bank, and the ▼ pedal

the next lower bank.

• In Edit (Manual) mode

The ▲ pedal serves to set the delay time of the effect

module. Each tap of the pedal changes the setting by one

step. The ▼ pedal serves to switch PRE for the effect

module on and off. The pedal LED lights up when PRE is

on.

(12) Pedal switches 1 - 4

• In Play mode

The pedals serve to select a patch. The respective pedal

LED lights up.

• In Edit (Manual) mode

The pedals serve to switch the effect modules EQ,

MODULATION, DELAY, REVERB on and off. The

respective pedal LED lights up.

(13) VOL (Volume) pedal

Serves to manually control the overall level of a patch.

(14) EXP (Expression) pedal

Serves to control any selected effect parameter in real time.

Rear Panel

(1) INPUT GAIN SWITCH

This switch controls the input sensitivity. Select the position

most suited to the connected instrument. For reference,

standard settings are shown below.

H: For guitars with single-coil pickups

M: For guitars with hum-bucking or active type pickups

L: For guitars with very high output

(2) INPUT jack

Serves for connection of an instrument such as electric

guitar or bass.

(3) EXTERNAL SEND/RETURN connectors

Serve for connection of an external effect device. The

send/return loop is inserted in series between the

compressor and distortion sections in the PRE module. The

ON/OFF setting of the send/return loop can be stored as part

of a patch.

(4) OUTPUT L/MONO & R connectors

Serves for connection to a guitar amplifier. To use the 4040

in stereo, connect cables to both jacks. For a monaural

setup, connect the cable to the L/MONO jack.

(5) PHONES jack

Allows connection of a pair of stereo headphones, to

monitor the output of the 4040.

(6) VOLUME control

Adjusts the master volume (overall output level of the

4040). The control affects both the signal at the OUTPUT

connectors and the PHONES jack.

(7) MANUAL connector

This jack serves for connection of the optional foot switch

FS01 which can be used to switch between Play mode and

Manual mode.

(8) EXTERNAL CONTROL OUT connector

This jack can be used to control channel switching of an

external guitar amplifier.

This setting can be stored as part of a patch.

(9) MIDI OUT connector

Serves for connection of a device with MIDI input, such as

another effect or a synthesizer. The setting can be stored as

part of a patch.

(10) DC INPUT (AC adapter) jack

The supplied AC adapter is connected here.

(11) POWER switch

Serves to turn the 4040 on and off.

POWERDC9V 200mA

EXT

CTRL OUT

MANUALVOLUMEPHONESL/MONO

OUTPUT

RRETURN

EXT

SENDINPUT

INPUT GAIN

HML

MODEL 4040 ZOOM CORPORATION

MADE IN JAPAN/FABRIQUE AU JAPON SERIAL NO

MIDI OUT

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11)

1 2 3 4 5 6 7 8 9 10 11 ... 28 29

Comments to this Manuals

No comments

Zoom Pro 4040 Specifications Page 6

Comments to this Manuals

Related products and manuals for Music Pedal Zoom Pro 4040