Zoom B9.1ut Specifications download pdf (Page 12)

Using the Internal Tuner (Bypass/Mute Condition)

ZOOM G7.1ut

STR1

STR2

STR3

STR4

STR5

STR6

STR7

GUITAR BASS OPEN A OPEN G OPEN E OPEN D DADGAD

Tuner type

String

number

Using other tuner types

Besides chromatic tuning, the G7.1ut offers

various other tuning types such as standard tuning

for guitar and bass, open tuning, etc. To use these

functions, proceed as follows.

1. Switch the G7.1ut to the bypass or

mute condition as described in step 1

of "Using the chromatic tuner".

The display shows the tuning indication.

2. Turn parameter knob 2 to select the

tuner type.

The available tuner types and the corresponding

note names for each string are listed below.

If you select "OPEN A" as tuner type, the

[GROUP/BANK] indicator and display indication

will be as follows.

3. If necessary, turn parameter knob 3

to change the reference pitch of the

tuner.

The setting range is center A = 435 – 445 Hz, in

1-Hz steps.

If "GUITAR" or "BASS" has been selected as

tuner type, turning parameter knob 3 further

anticlockwise from the "435" setting selects the

setting "b" (one semitone lower), "bb" (two

semitones lower), and "bbb" (three semitones

lower).

HINT

When the G7.1ut is turned off and on again, the

reference pitch will be reset to 440 Hz.

4. Play the open string of the indicated

number and adjust the pitch.

5. Turn parameter knob 4 to switch to

other strings.

6. Tune other strings in the same way.

7. When tuning is completed, press one

of the BANK [W]/[Q] foot switches.

The G7.1ut returns to the previous mode. If the

G7.1ut was in edit mode, it will be switched to

play mode.

HINT

When the G7.1ut is turned off and on again, the

tuner type setting will be reset to the default

(chromatic tuner).

Tuner type Reference pitch

String numbe

Correct note for selected string

˙<

¢Str2

Str2

™OPEN A

OPEN A

£440Hz

440Hz

Optional tuning to 1 - 3 semitones lowe

˙<

¢Str1

Str1

™GUITAR

GUITAR

ZOOM G7.1ut

Channel A

Channel B

INPUT

EQPRE-AMPZNR

COMP WAH/EFX1 MOD/EFX2

CABINET

DELAY REVERB

Pre-amp section

[Patch configuration]

Changing the Sound of a Patch (Edit Mode)

The condition where you can change the effect types and settings that make up a patch is called "edit

mode". This section describes how to use this mode.

Patch configuration

As shown in the "Patch configuration" illustration

below, the G7.1ut can be thought of as a series of

several single effects (effect modules). A

combination of these modules and the settings for

each module are stored as a patch.

Almost all modules comprise several different

effects (called effect types), one of which is

selected at any given time. For example, the

MOD/EFX2 module allows selection of either

CHORUS, PITCH SHIFTER, DELAY, etc.

The elements that determine the sound of a patch

are called effect parameters. Each effect type has

its own parameters that can be controlled with

knobs on the panel. Even within the same module,

when the effect type is different, the effect

parameters that can be controlled will also be

different.

In the module configuration shown below, the

ZNR, PRE-AMP, EQ, and CABINET modules

operate as a virtual pre-amp section. Depending

on the application, this section can be inserted

after the WAH/EFX1 module or after the DELAY

module (→ p. 52). For the ZNR, PRE-AMP and

EQ modules, different settings can be made in

two channels (A/B).

Basic edit mode steps

The basic steps that are normally taken in edit

mode are explained here. For details on effect

types and parameters for each module, see the

section "Effect Types and Parameters" on page 54

– 67.

1. Select the patch to edit.

The patch can be from a preset group (A/b) or

user group (U/u). However, if you have edited a

patch from a preset group, it can only be stored in

a user group (→ p. 27).

2. In play mode or manual mode, press

the effect module key (see illustration

on next page) to select the module on

which to operate.

The G7.1ut switches to edit mode, and the display

changes as follows.

HINT

• On every display screen, the number shown in

reverse indicates the parameter knob that can

be used to adjust the parameter.

Module name

Parameter

number

Currently selected

parameter and its setting

value

Effect type name

[Module other than PRE-AMP/EQ]

¡Depth =100

Depth =100

MOD:Chorus

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 40 41

Comments to this Manuals

No comments

Zoom B9.1ut Specifications Page 12

Comments to this Manuals

Related products and manuals for Musical Equipment Zoom B9.1ut