Zoom Tri Metal TM-01 Specifications download pdf (Page 18)

Effect Types and Parameters

ZOOM G2.1u

"UP"

Maximum value

Minimum value

Maximum value

alue set in patch

Minimum value

"DOWN"

"HIGH"

"LOW"

CONTROL

CONTROL module

Serves for making pedal settings and lets you control the foot switch function and master

level setting applying to all patches.

RTM DESTINATION

See Table 4

See Table 5

MASTER LEVEL

0 – 98, 1.0

When an expression pedal (FP01/FP02)

is connected to the [CONTROL IN]

jack, this selects the modulation target

module for the RTM function (See Table

4).

When a foot switch (FS01) is connected

to the [CONTROL IN] jack, this selects

the function that can be operated with

the foot switch (See Table 5). The

function selected here applies to all

patches.

Adjusts the master level for all patches.

Table 4 Table 5

Setting Modulation target Setting Function

OFF

Bypass/Mute

Volume

Tap tempo

WU, Wd, WH, WL

WAH/EFX module (*)

Bank up

GU, Gd, GH, GL

DRIVE module (*)

Rhythm function on/off

MU, Md, MH, ML

MOD/SFX module (*)

Delay hold

dU, dd, dH, dL

DELAY module (*)

Delay mute

rU, rd, rH, rL

REVERB module (*)

The operation of modules denoted by (*)

changes as follows, according to the letter at

right.

The parameter is at minimum when the pedal is

fully raised and at maximum when the pedal is fully

pushed down.

DOWN

The parameter is at maximum when the pedal is

fully raised and at minimum when the pedal is fully

pushed down.

HIGH

When the pedal is fully raised, the parameter is at

the value set in the patch. When the pedal is fully

pushed down, the parameter is at maximum.

LOW

When the pedal is fully raised, the parameter is at

minimum. When the pedal is fully pushed down,

the parameter is at the value set in the patch.

ZOOM G2.1u

Specifications

Effect types 54

Effect modules Max. 9 simultaneous modules

Patches User area: 10 patches x 4 banks

Preset area: 10 patches x 4 banks

Sampling frequency 96 kHz

A/D converter 24 bit, 64 times oversampling

D/A converter 24 bit, 128 times oversampling

Signal processing 32 bit

Frequency response 20 Hz – 40 kHz +1 dB -3 dB (with 10 kilohms load)

Display 2-digit 7-segment LED

Parameter LEDs, Pedal assign LEDs

Input Standard mono phone jack

Rated input level -20 dBm

Input impedance 1 megohm

Output Standard stereo phone jack (doubles as line and headphone jack)

Maximum output level Line: +5 dBm (output load impedance 10 kilohms or more)

Phones: 20 mW + 20 mW (into 32 ohms load)

Control input For FP02/FS01

USB interface

PC interface: 16-bit (stereo configuration for recording/playback)

Sampling frequency: 44.1 kHz, 48 kHz

Power requirements

AC adapter9 V DC, 300 mA (center minus plug) (ZOOM AD-0006)

Batteries Four IEC R6 (size AA) batteries,

Approx. 7.5 hours continuous operation (alkaline batteries)

Dimensions 165 mm (D) x 255 mm (W) x 79mm (H)

Weight 1100 g (without batteries)

Options Expression pedal FP02/ Foot switch FS01

• 0 dBm = 0.775 Vrms

• Design and speciﬁcations subject to change without notice.

Troubleshooting

● No power

Refer to "Turn power on" on page 8.

● Reverb effect does not operate

While a rhythm pattern is playing, the reverb effect is not available. Stop the rhythm pattern first

(→ p. 12).

● High level of noise

Is ZOOM AC adapter being used? Be sure to use only adapter for 9 V DC, 300 mA with center

minus plug (ZOOM AD-0006).

● Battery life is short

Are manganese batteries being used? The use of alkaline batteries is recommended.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 24 25

Comments to this Manuals

No comments

Zoom Tri Metal TM-01 Specifications Page 18

Comments to this Manuals

Related products and manuals for Guitar accessories Zoom Tri Metal TM-01